|
|
|
Shanghai Bagen Electronic Science & Technology Co., Ltd
|
|
| |
|
|
|
|
|
|
 Click to enlarge image
|
Working principle
YASH® mirror defoggers are adhesive heating pads, when installed onto the back of mirror. They provide heat energy, which transfers directly to the mirror, resulting in a warming of mirror surface. This gets rid of the mist. So every time you step out from the shower or bath, you no longer have to wait for the mist to clear before shaving, drying your hair or putting make up on.
Technical parameters
A:Voltage :12V-24V, 120V-220V
B : Input power: 2.0-2.5w/dm
E: Double insulated layers
F: self-adhesive backing
C: Average Temperature Rise: 15-18 °C
D: Thickness: 0.4mm
Features:
Safe to use, (CE, UL approval)
Easy to install,
Low cost
Temperature is self-regulating
Other advantages over normal mirror:
Prevents moisture damage to silver coatings
Retains mirror in the place in the event of breakage
Reduces need for cleaning
INSTALLATION INSTRUCTION
Safety points:
1. yash Defogger is designed to be used as a bathroom mirror defogger only. Install in accordance with these instructions. Any other use is not recommended.
2. Installation is not difficult and conforms to standard industry practice. As with any electrical product, we do recommend installation be performed by a qualified person in accordance with local codes. Remember to disconnect power at the fuse breaker panel before installation.
3, The heating element of mirror defogger should never be cut or damaged. This will render the product useless. It cannot be repaired. Please take particular care over this point.
4, However you may trim the product so long as the actual heating element is NOT damaged, which is common for yash oval and round series. Round and oval Defoggers should have excess adhesive backing material trimmed, but not closer than 20 mm from the electrical heating grid component.
5, The power supply cable of the defogger should not be pulled or drawn forcefully in case of damage.
FITTING THE HEATER TO THE MIRROR
1.Adhere the heater pad to the back of the mirror, NOT to the wall.
2.Always handle mirrors with care. Lay the mirror face down on a protective cushion/surface
3.The back of the mirror must be absolutely clean, dry and grease free.
4.Peel off the protection paper first in about 10cm width and fold the paper, adhere the heater with self-backing directly onto the back of the mirror, using towel or some other soft rubber to wipe the back of the defogger. In the mean time, rip off the protection paper to stick the defogger onto the mirror easily.
5.Ensure that there are no trapped air bubbles and that the heater is positioned where you would like.
INSTALL THE HEATED MIRROR ONTO THE WALL
The wall will be installed electric heated mirror can be wood, ceramic tile, marble and so on, which must be dry, stable, even otherwise, the heated mirror will be uneven.
The place that the heated mirror will be installed should be wiring snugly. eg, lighting circuit.
Before install mirror, properly apply some clear silicon around the mirror by glue gun onto the surface of wall that will install mirror. Or if the mirror rests on clips, place a layer of silicon on the bottom of the clips.
Please allow a 2mm gap between the mirror and hard substances (eg ceramic brick, marble, tiles as well as metal and wood periphery around mirrors) If you have metal periphery, please ensure the mirror is earthed in line with regulations.
ELECTRICAL INSTALLATION INFORMATION
Connect the wires of the defogger with the power code following the electronic standards.
The power supply cable may be conveniently taken to the lighting circuit.
The heater should be switched. Which can be wired a simple switch, light fixture or fan. We always recommend our heaters are switched with bathroom lights so that it comes on and off with the lights.
Fix the mirror onto wall by silicon or clips, then apply neutral silicon again to seal around the edge of the mirror, which is the same way with normal mirror.
Turn on the electricity and test the mirror. about 3-5minuters, the mirror becomes warm and defogging.
The manufacturer/supplier cannot be held responsible for damage caused by improper installation
|
|
|
|
| |
|
|
|
Related Keywords:
Bookmark / Share this page